Ampere-v2.01_hanif6867.apk

Ampere Pro v2.01 Final
Requirements: 4.0.3
Overview: Did we ever felt, that one Charger/USB wire set charges your device unequivocally quick and a other not? Now, we can infer this with Ampere.



Measure a charging and discharging stream of your battery.

PRO features:
– Widgets
– Notification
– Alerts on device
– Alerts on Android Wear

The app works on Android 4.0.3 devices. Not each device is upheld since there are inclination that lacks an suitable dimensions chip (or a interface) and they can not be upheld during all. Please review a list of not upheld phones during a finish of a description.

The app is not meant to be mA accurate. It is usually good for weigh that Charger/USB wire combo is operative a best for we on a same device.

—-

Please review also a FAQ: SPAM | Lost in Cyberspace

—-

Start a app and wait ca. 10 seconds (“measuring” is on a display). After this time, a charging or discharging stream will be shown.

The stream depends on many things:
– Charger (USB/AC/Wireless)
– USB cable
– Phone type
– Current tasks running
– Display brightness
– WiFi state
– GPS state

Please don’t use a readings on this app as petrify science. However, a readings are good adequate to comparatively magnitude how several chargers and USB cables satisfactory on a same device.

If a app shows 0mA all a time, greatfully use a settings choice “Old dimensions method”. You can force a app with it to use a aged dimensions interface, if a Lollipop device has during slightest one.

Unfortunately some Samsung inclination don’t give scold (measured) values (e..: S5), usually a limit probable charging stream with a tangible USB cable/charger configuration. This is a firmware problem.

—-

Background info: The app measures a charging/discharging stream of a battery. If your phone is not connected to a charger, we see a discharging stream that is negative. If we bond a horse afterwards a stream what a horse gives will be used to supply your phone and a remaining energy will be charged into a battery.

If your phone consumes 300 mA though a horse connected (-300mA on a display), afterwards a 500 mA horse will assign your battery limit with 200 mA stream (200mA on display).

—-

Technical info: The displayed stream is an normal value from 50 measurements reduction a 10 top values and a 10 reduce values. The displayed stream can be unsure or inconstant or even 0 that means, that a Android complement provides inconstant values. Every association uses opposite battery forms and other hardware creation it formidable to get accurate formula about your charger.

—-

LiPo batteries don’t pull a limit for a full time it takes to assign a phone. If your battery is charged roughly full afterwards a charging stream will be most reduction as by reduce battery levels.

– A graph explaining LiPo assign stages: http://batteryuniversity.com/_img/content/ion1.jpg
– Dave’s (EEVBlog) LiPo Charging Tutorial: EEVblog #176 – Lithium Ion/Polymer Battery Charging Tutorial – YouTube

—-

Phones/ROMS concordant usually with “Old dimensions method” switched on and comparison a right “Measurement interface”:
➤ HTC One M7 / M8
➤ LG G3

Phones/ROMS reported to be not operative with this app:
➤ Galaxy Grand Prime – fortuna3gdtv
➤ Galaxy Note2 – t03g, t03gchn, t03gchnduos, t03gcmcc, t03gctc, t03gcuduos

➤ Galaxy S3 – d2att, d2spr, d2vmu
➤ Galaxy Tab4 7.0 – degas3g
➤ HTC Desire 510 – htc_a11ul8x26
➤ HTC One S (ville), X (endeavoru), XL (evita)
➤ HTC Sensation 4G – pyramid

Please do not give wrong rating, if your phone is one of a above. Not a app is wrong, though your phone does not support this kind of dimensions yet.

If a app doesn’t work on your device with pre-Lollipop Android version, afterwards greatfully review a initial and a second posts in this XDA developer forum thread: SPAM | Lost in Cyberspace . Please post your problem with screenshots in a XDA thread

WHAT’S NEW

v2.01:
* New translations: Albanian, Lithuanian, Japanese
* Bug fixes

This app has no advertisements